人妻少妇精品视频专区网址,成人免费黄色的视频,国产亚洲欧美日韩国亚语

支承滾輪

日期： 2017/1/3 15:03:27

外徑 Outside Diameter	軸承型號與近似重量注1 Bearing Designation and mass approx				外形尺寸 Borndary Dimensions						基本額定負荷注2 Basic Load Rating				極限轉速 Limiting Speed
	無內圈 Without IR	重量 Mass	帶內圈 With IR	重量 Mass	D	d	F注1 Fw	B	C	E	動 Cr Dynamic	靜 Cor Static	作為支承滾輪		脂潤滑注3 Grease
		重量 Mass		重量 Mass	D	d	F注1 Fw	B	C	E	動 Cr Dynamic	靜 Cor Static	動 Cw	靜 Cow	脂潤滑注3 Grease
mm		g		g	mm						N				rpm
16	RSTO 5 TN	8.5	--	--	16	--	7	--	7.8	10	2800	2600	2550	2550	23000
16	RSTO 5 TN X	8.5	--	--	16	--	7	--	7.8	10	2800	2600	1990	1990	23000
19	RSTO 6 TN	12.5	STO 6 TN	17	19	6	10	10	9.8	13	4700	5450	3750	4500	20000
19	RSTO 6 TN X	12.5	STO 6 TN X	17	19	6	10	10	9.8	13	4700	5450	3050	4000	20000
24	RSTO 8 TN	21	STO 8 TN	26	24	8	12	10	9.8	15	4800	6000	4200	5500	16000
24	RSTO 8 TN X	21	STO 8 TN	26	24	8	12	10	9.8	15	4800	6000	3000	5000	16000
30	RSTO 10	42	STO 10	49	30	10	14	12	11.8	20	10200	10500	8400	9200	11000
30	RSTO 10 X	42	STO 10 X	49	30	10	14	12	11.8	20	10200	10500	8000	8800	11000
32	RSTO 12	49	STO 12	57	32	12	16	12	11.8	22	11300	12300	8900	10100	9000
32	RSTO 12 X	49	STO 12 X	57	32	12	16	12	11.8	22	11300	12300	8500	9600	9000
35	RSTO 15	50	STO 15	63	35	15	20	12	11.8	26	13200	16000	9100	10700	6500
35	RSTO 15 X	50	STO 15 X	63	35	15	20	12	11.8	26	13200	16000	8700	9900	6500
40	RSTO 17	88	STO 17	107	40	17	22	16	15.8	29	19800	25300	14300	17700	5500
40	RSTO 17 X	88	STO 17 X	107	40	17	22	16	15.8	29	19800	25300	12500	15700	5500
47	RSTO 20	130	STO 20	152	47	20	25	16	15.8	32	20800	27800	16200	21500	4700
47	RSTO 20 X	130	STO 20 X	152	47	20	25	16	15.8	32	20800	27800	15000	19900	4700
52	RSTO 25	150	STO 25	177	52	25	30	16	15.8	37	23000	33400	16500	22900	3600
52	RSTO 25 X	150	STO 25 X	177	52	25	30	16	15.8	37	23000	33400	14000	20900	3600
62	RSTO 30	255	STO 30	308	62	30	38	20	19.8	46	35200	56700	23300	35000	2500
62	RSTO 30 X	255	STO 30 X	308	62	30	38	20	19.8	46	33200	56700	21800	33000	2500
72	RSTO 35	375	STO 35	441	72	35	42	20	19.8	50	35800	58800	26000	41000	2200
72	RSTO 35 X	375	STO 35 X	441	72	35	42	20	19.8	50	35800	58800	24500	38900	2200
80	RSTO 40	420	STO 40	530	80	40	50	20	19.8	58	35200	61800	24000	39000	1700
80	RSTO 40 X	420	STO 40 X	530	80	40	50	20	19.8	58	35200	61800	22500	36500	1700
85	RSTO 45	453	STO 45	576	85	45	55	20	19.8	63	38900	73900	25500	43000	1500
85	RSTO 45 X	453	STO 45 X	576	85	45	55	20	19.8	63	38900	73900	24000	41500	1500
90	RSTO 50	481	STO 50	617	90	50	60	20	19.8	68	43300	84800	26000	46500	1300
90	RSTO 50 X	481	STO 50 X	617	90	50	60	20	19.8	68	43300	84800	22800	44000	1300

TN=塑料保持架，允許工作溫度：120°C連續；180°C短期。

1）F是內圈滾道直徑，Fw是具F6公差范圍內的滾針內切圓直徑。

2)當軸承外圈（有外圈柱表面）裝入具有一般配合的座孔中時，使用基本額定負荷Cr和Cor；當用作支承滾輪時，使用額定負荷Cw和Cow。

3）使用油潤滑時，極限轉速增加約30％。

1）TN=plastic cage,permissible operating temperature:120°C(continuous operation).

F=raceway diameter of innerring.

Fw=needle roller enveloping circle in the tolerance zone F6.

2)The basic load ratings C and C0 apply if the bearing outerring(with cylindrical outside surface) is mounted in a housing bore with the normal rolling bearing fit; when used as a track roller,the load ratings Cw and Cow apply.

3)Limiting speed for grease lubrication.with oil lubrication,the speed can be increased by approximately 30%.

外徑 Outside Diameter	軸承型號與近似重量注1 Bearing Designation and mass approx				外形尺寸 Borndary Dimensions						基本額定負荷注2 Basic Load Rating				極限轉速 Limiting Speed
	無內圈 Without IR	重量 Mass	帶內圈 With IR	重量 Mass	D	d	F注1 Fw	B	C	E	動 Cr Dynamic	靜 Cor Static	作為支承滾輪		脂潤滑注3 Grease
		重量 Mass		重量 Mass	D	d	F注1 Fw	B	C	E	動 Cr Dynamic	靜 Cor Static	動 Cw	靜 Cow	脂潤滑注3 Grease
mm		g		g	mm						N				rpm
19	RNA 22/6.2RS	18	NA 22/6.2RS	22	19	6	10	12	11.8	16	5000	4350	3050	3000	18000
19	RNA 22/6.2RS X	18	NA 22/6.2RS X	22	19	6	10	12	11.8	16	5000	4350	3900	3700	18000
24	RNA 22/8.2RS	29	NA 22/8.2RS	34	24	8	12	12	11.8	18	5500	5200	4800	4800	14000
24	RNA 22/8.2RS X	29	NA 22/8.2RS X	34	24	8	12	12	11.8	18	5500	5200	4050	4050	14000
30	RNA 2200.2RS	52	NA 2200.2RS	60	30	10	14	14	13.8	20	7600	8100	7000	8000	11000
30	RNA 2200.2RS X	52	NA 2200.2RS X	60	30	10	14	14	13.8	20	7600	8100	6500	7050	11000
32	RNA 2201.2RS	57	NA 2201.2RS	67	32	12	16	14	13.8	22	8500	9700	7500	9000	9500
32	RNA 2201.2RS X	57	NA 2201.2RS X	67	32	12	16	14	13.8	22	8500	9700	7050	8950	9500
35	RNA 2202.2RS	60	NA 2202.2RS	75	35	15	20	14	13.8	26	9600	12000	7600	9600	7000
35	RNA 2202.2RS X	60	NA 2202.2RS X	75	35	15	20	14	13.8	26	9600	12000	7050	9080	7000
40	RNA 2203.2RS	94	NA 2203.2RS	112	40	17	22	16	15.8	28	12000	16500	9900	13800	6000
40	RNA 2203.2RS X	94	NA 2203.2RS X	112	40	17	22	16	15.8	28	12000	16500	9090	11800	6000
47	RNA 2204.2 RS	152	NA 2204.2RS	177	47	20	25	18	17.8	33	18500	21900	15200	18300	4600
47	RNA 2204.2RS X	152	NA 2204.2RS X	177	47	20	25	18	17.8	33	18500	21900	13500	16500	4600
52	RNA 2205.2RS	179	NA 2205.2RS	209	52	25	30	18	17.8	38	20100	26000	15700	20000	3500
52	RNA 2205.2RS X	179	NA 2205.2RS X	209	52	25	30	18	17.8	38	20100	26000	13500	18900	3500
62	RNA 2206.2RS	284	NA 2206.2RS	324	62	30	35	20	19.8	43	23000	28000	18300	25500	2800
62	RNA 2206.2RS X	284	NA 2206.2RS X	324	62	30	35	20	19.8	43	23000	28000	17500	23500	2800
72	RNA 2207.2RS	432	NA 2207.2RS	505	72	35	42	23	22.7	50	29800	46300	23000	35500	2200
72	RNA 2207.2RS X	432	NA 2207.2RS X	505	72	35	42	23	22.7	50	29800	46300	20500	32500	2200
80	RNA 2208.2RS	530	NA 2208.2RS	628	80	40	48	23	22.7	57	38200	57700	27500	40500	1700
80	RNA 2208.2RS X	530	NA 2208.2RS X	628	80	40	48	23	22.7	57	38200	57700	25000	38000	1700
85	RNA 2209.2RS	545	NA 2209.2RS	655	85	45	52	23	22.7	62	40300	63800	28500	43000	1600
85	RNA 2209.2RS X	545	NA 2209.2RS X	655	85	45	52	23	22.7	62	40300	63800	26000	41000	1600
90	RNA 2210.2RS	563	NA 2210.2RS	690	90	50	58	23	22.7	68	42100	66000	28000	42500	1300
90	RNA 2210.2RS X	563	NA 2210.2RS X	690	90	50	58	23	22.7	68	42100	66000	26000	40500	1300

1）F是內圈滾道直徑，Fw是具F6公差范圍內的滾針內切圓直徑。

2)當軸承外圈（有外圈柱表面）裝入具有一般配合的座孔中時，使用基本額定負荷Cr和Cor；當用作滾輪時，使用額定負荷Cw和Cow。

3）使用油潤滑時，極限轉速增加約30％。

1）F=raceway diameter of innerring.

Fw=needle roller enveloping circle in the tolerance zone F6.

3)Limiting speed for grease lubrication.with oil lubrication,the speed can be increased by approximately 30%.

外徑 Outside Diameter	軸承型號與近似重量注1 Bearing Designation and mass approx				外形尺寸 Borndary Dimensions					基本額定負荷注2 Basic Load Rating				極限轉速 Limiting Speed
	不帶密封 Without seal	重量 Mass	帶密封 Sealed	重量 Mass	d	D	B	C	d1	動 Cr Dynamic	靜 Cor Static	作為支承滾輪		脂潤滑注3 Grease
		重量 Mass		重量 Mass	d	D	B	C	d1	動 Cr Dynamic	靜 Cor Static	動 Cw	靜 Cow	脂潤滑注3 Grease
mm		g		g	mm					N				rpm
16	NATR 5	14	NATR 5 PP	14	5	16	12	11	12	3050	3000	2050	2400	22000
16	NATV 5	15	NATV 5 PP	15	5	16	12	11	12	4500	6300	3680	4300	8500
19	NATR 6	20	NATR 6 PP	20	6	19	12	11	14	3600	3650	2450	2850	20000
19	NATV 6	21	NATV 6 PP	21	6	19	12	11	14	5700	8700	4600	6750	7000
24	NATR 8	41	NATR 8 PP	41	8	24	15	14	19	4500	5400	3900	4500	5000
24	NATV 8	42	NATV 8 PP	42	8	24	15	14	19	8600	12000	6700	9800	5500
30	NATR 10	64	NATR 10 PP	64	10	30	15	14	23	6100	7800	4500	6900	11000
30	NATV 10	65	NATV 10 PP	65	10	30	15	14	23	10900	17000	7600	11800	4500
32	NATR 12	71	NATR 12 PP	71	12	32	15	14	25	6600	9800	4660	7000	9000
32	NATV 12	72	NATV 12 PP	72	12	32	15	14	25	11800	19000	7800	13000	3900
35	NATR 15	103	NATR 15 PP	103	15	35	19	18	27	10500	17500	7800	11500	7000
35	NATV 15	105	NATV 15 PP	105	15	35	19	18	27	16000	32500	10200	20500	3400
40	NATR 17	144	NATR 17 PP	144	17	40	21	20	32	11800	19400	9500	13500	6000
40	NATV 17	152	NATV 17 PP	152	17	40	21	20	32	19600	37000	1200	23000	2900
47	NATR 20	246	NATR 20 PP	246	20	47	25	24	37	17500	29800	13500	22500	4900
47	NATV 20	254	NATV 20 PP	254	20	47	25	24	37	25800	57000	19000	39500	2600
52	NATR 25	275	NATR 25 PP	275	25	52	25	24	42	19500	36500	13400	23500	3600
52	NATV 25	285	NATV 25 PP	285	25	52	25	24	42	29000	69600	19800	40900	2100
62	NATR 30	470	NATR 30 PP	470	30	62	29	28	51	31000	57500	20900	35500	2600
62	NATV 30	481	NATV 30 PP	481	30	62	29	28	51	45500	104000	27800	60900	1700
72	NATR 35	635	NATR 35 PP	635	35	72	29	28	58	34500	67500	22500	41000	2000
72	NATV 35	647	NATV 35 PP	647	35	72	29	28	58	50800	109500	30900	70800	1400
80	NATR 40	805	NATR 40 PP	805	40	80	32	30	66	47000	91500	30900	56500	1700
80	NATV 40	890	NATV 40 PP	890	40	80	32	30	66	64000	139000	39800	87800	1300
85	NATR 45	910	NATR 45 PP	910	45	85	32	30	72	49100	98000	30600	56900	1500
90	NATR 50	960	NATR 50 PP	960	50	90	32	30	76	50500	10600	30600	57500	1300
90	NATV 50	990	NATV 50 PP	990	50	90	32	30	76	69500	187000	38700	90900	1000

1）后綴“X”表示為圓柱形外表面，例如：NATR 5 X或NATR 5 PP X。

2)當軸承外圈（有外圈柱表面）裝入具有一般配合的座孔中時，使用基本額定負荷Cr和Cor；當用支承作滾輪時，使用額定負荷Cw和Cow。

3）使用油潤滑時，極限轉速增加約30％。*密封型的極限轉速應減低30％。

1）The suffix Xindicates a cylindrical outside surface e.g.NATR 5 X or NATR 5 PP X.

2)The basic load ratings C and C0 apply if the bearing outer ring(with cylindrical outside surface) is mounted in a housing bore with the normal rolling bearing fit; when used as a track roller,the load ratings Cw and Cow apply.

3)Limiting speed for grease lubrication. with oil lubrication,the speed can be increased by approximately 30% except for the sealed executions.*For the sealed version the limiting speed ng for grease lubrication should be reduced by approximately 30%.

外徑 Outside Diameter	軸承型號與近似重量注1 Bearing Designation and mass approx		外形尺寸 Boundary Dimensions					基本額定負荷注2				極限轉速 Limiting Speed
	有內圈 With IR	重量 Mass	d	D	B	C	d1	動Cr Dynamic	靜Cor Static	作為支承滾輪		脂潤滑注3 Grease
		重量 Mass	d	D	B	C	d1	動Cr Dynamic	靜Cor Static	動Cw	Cow	脂潤滑注3 Grease
mm		g	mm					N				rpm
35	NUTR 15	99	15	35	19	18	20	20500	24500	13900	15300	6500
40	NUTR 17	147	17	40	21	20	22	21800	28500	16500	20500	5500
42	NUTR 15 42	158	15	42	19	18	20	20500	24500	16800	21800	6500
47	NUTR 17 47	220	17	47	21	20	22	21800	28500	19000	25000	5500
47	NUTR 20	245	20	47	25	24	27	36900	48900	26000	33500	4200
52	NUTR 20 52	321	20	52	25	24	27	36900	48900	29800	39800	4200
52	NUTR 5	281	25	52	25	24	31	40800	58500	27500	35000	3400
62	NUTR 25 62	450	25	62	25	24	31	40800	58500	32500	47800	3400
62	NUTR 30	465	30	62	29	28	38	56800	77500	39500	49500	2600
72	NUTR 30 72	697	30	72	29	28	38	56800	77500	46000	62800	2600
72	NUTR 35	630	35	72	29	28	44	63000	91000	42500	59000	2100
80	NUTR 35 80	836	35	80	29	28	44	63000	91000	49500	70500	2100
80	NUTR 40	816	40	80	32	30	51	87900	108000	54000	73600	1600
85	NUTR 45	883	45	85	32	30	55	93600	119000	54000	77500	1400
90	NUTR 40 90	1129	40	90	32	30	51	87900	108000	63800	93600	1600
90	NUTR 50	950	50	90	32	30	60	98900	140000	55900	79000	1300
100	NUTR 45 100	1396	45	100	32	30	55	93600	119000	70500	106000	1400
110	NUTR 50 110	1690	50	110	32	30	60	98900	140000	73600	118000	1300

1）后綴“X”表示為圓柱形外表面，例如：KR 16 X。

2)當軸承外圈（有外圈柱表面）裝入具有一般配合的座孔中時，使用基本額定負荷Cr和Cor；當用支承作滾輪時，使用額定負荷Cw和Cow。

1）The suffix X indicates a cylindrical outside surface e.g.KR 16 X.

2)The basic load ratings C and C0 apply if the bearing outer ring(with cylindrical outside surface) is mounted in a housing bore with the normal rolling bearing fit; when used as a track roller,the load ratings Cw and Cow apply.

上一個：滾針、滾子
下一個：曲線滾輪

最新晚上碰碰精品视频_亚洲v国产v天堂a无码二区久久互动交流_曰批全过程又爽又大又黄_国产人成在线观看_午夜福利视频网站_日韩av无码不卡免费毛片_夜夜春天天弄精品视频_中文字幕一本在线

首頁 > 技術資料